IE Shield

18.50

IE shield is an Ethernet shield which use the ENC28J60 chip for Arduino. It integrates one Micro-SD card slot and provides main interface breakout. You can use it with Arduino to build your Ethernet development platform.

Laost otsas

Kategooriad: ,

Kirjeldus

IE shield is an Ethernet Shield instantly enables internet connectivity for Arduino projects with ethernet controller ENC28J60.  Just stack it onto an Arduino to create your own networked devices. Easily check connection status with on board indicator lights. Extend your design further with many Electronic / Sensor  brick interface and an TF card socket.

This Ethernet shield support the POE function, you can use use the twisted-pair to power it and the Arduino board below, instead using the USB prower or external power jack supply. If your router or moden don’t support POE, then you can use the injector cable to mix the signale and power for POE supply.

Features

  • IEEE 802.3 compatible
  • Supports POE*
  • Integrated MAC and 10BASE-T PHY
  • Receiver and collision squelch circuit
  • Supports one 10BASE-T port with automatic polarity detection and correction
  • Supports Full and Half-Duplex modes
  • Programmable automatic retransmit on collision
  • Programmable padding and CRC generation
  • Programmable automatic rejection of erroneous packets
  • Two programmable LED outputs for LINK, TX, RX, collision and full/half-duplex status
  • Supports Micro-SD card with SPI operation
  • Much analog and digital interfaces breakout include AD/DA/PWM/UART/IIC/GPIO

 

Hardware

Interface Pin Description
UART 1 5V supply.
2 Ground
3 Tx
4 Rx
GPI 1 5V supply.
2 Digital input pin
3 Ground
GPO 1 5V supply.
2 Digital output pin
3 Ground
DA 1 5V supply.
2 Analog output pin
3 Ground
PWM 1 5V supply.
2 PWM output pin
3 Ground
AD0/1/2 1 5V supply.
2 Analog input pin
3 Ground
IIC 1 5V supply.
2 Ground
3 Data wire of IIC
4 Clock wire of IIC
Ethernet module SPI 1 5V supply.
2 Ground
3 Chip select pin(Low active)
4 Chip reset pin(Low active)
5 Chip data input pin
6 Chip clock input pin
7 Weak on Line output pin(Low active)
8 Chip data output pin
9 Chip programmable clock output pin
10 Interrupt output pin(Low active)

 

 

Specification

Version 1.1
Compatible Mainboard
  • Arduino Deumlanove/UNO
  • Arduino MEGA
  • Iteaduino
  • Iteaduino BT
  • Iteaduino ADK
  • Iteaduino MEGA 2560
  • Iteadmaple
  • Simple Cortex
  • ChipKit UNO32
  • ChipKit MAX32
  • FEZ Panda II
  • Freeduino
  • Leaf maple
  • Seeeduino
  • Seeduino MEGA
Shield Functions
  • Storage
  • Ethernet
Board Size 69mm x 56mm
Operation Level Digital 5V
Stackable No
Model IM120417003
Accessories N/A
Weight 45.00g

 

 

Documents

Datasheet (emc28j60)
Datasheet (IE shield)
Schematic
Library (ENC28j60)
Library (SdFat)

Lisainfo

Kaal 45 g
Mõõtmed 69 × 56 mm

Arvustused

Tooteülevaateid veel ei ole.

Ole esimene, kes hindab toodet “IE Shield”

Sinu e-postiaadressi ei avaldata. Nõutavad väljad on tähistatud *-ga

This site uses Akismet to reduce spam. Learn how your comment data is processed.